Add TMK converter support to Next converter

- change protocol stack to LUFA
This commit is contained in:
tmk 2014-09-24 15:50:29 +09:00
parent dd3ab65ec3
commit 27967f2008
3 changed files with 126 additions and 1 deletions

View File

@ -20,6 +20,7 @@ CONFIG_H = config.h
MCU = atmega32u4 # Teensy 2.0
#MCU = at90usb646 # Teensy++ 1.0
#MCU = at90usb1286 # Teensy++ 2.0
#MCU = atmega32u2 # TMK converter
# Processor frequency.
@ -30,6 +31,29 @@ MCU = atmega32u4 # Teensy 2.0
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
@ -58,6 +82,6 @@ VPATH += $(TOP_DIR)
include $(TOP_DIR)/protocol.mk
include $(TOP_DIR)/protocol/pjrc.mk
include $(TOP_DIR)/protocol/lufa.mk
include $(TOP_DIR)/common.mk
include $(TOP_DIR)/rules.mk

View File

@ -0,0 +1,63 @@
# Target file name (without extension).
TARGET = next_usb
# Directory common source filess exist
TOP_DIR = ../..
# Directory keyboard dependent files exist
TARGET_DIR = .
# keyboard dependent files
SRC = keymap.c \
matrix.c \
led.c
CONFIG_H = config.h
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
#MCU = at90usb162 # Teensy 1.0
MCU = atmega32u4 # Teensy 2.0
#MCU = at90usb646 # Teensy++ 1.0
#MCU = at90usb1286 # Teensy++ 2.0
# Processor frequency.
# Normally the first thing your program should do is set the clock prescaler,
# so your program will run at the correct speed. You should also set this
# variable to same clock speed. The _delay_ms() macro uses this, and many
# examples use this variable to calculate timings. Do not add a "UL" here.
F_CPU = 16000000
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# *Comment out* to disable the options.
#
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys
EXTRAKEY_ENABLE = yes # Audio control and System control
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
#NKRO_ENABLE = yes # USB Nkey Rollover
SRC += next_kbd.c
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
include $(TOP_DIR)/protocol.mk
include $(TOP_DIR)/protocol/pjrc.mk
include $(TOP_DIR)/common.mk
include $(TOP_DIR)/rules.mk

View File

@ -60,6 +60,7 @@ POSSIBILITY OF SUCH DAMAGE.
//#define TEENSY_CONFIG 1
#define PRO_MICRO_CONFIG 1
//#define TMK_CONFIG 1
// comment out if you don't want the keyboard's LEDs to flash upon initialization
#define NEXT_KBD_INIT_FLASH_LEDS
@ -143,6 +144,43 @@ POSSIBILITY OF SUCH DAMAGE.
#endif
//================= End of Teensy 2.0 Configuration ==================
//================ Start of TMK converter Configuration =================
#ifdef TMK_CONFIG
// this is the debugging LED that flashes when a key is being pressed
// comment out in order to disable debugging LED
#define NEXT_KBD_LED1_PORT PORTD
#define NEXT_KBD_LED1_PIN PIND
#define NEXT_KBD_LED1_DDR DDRD
#define NEXT_KBD_LED1_BIT 6
#define NEXT_KBD_LED1_ON NEXT_KBD_LED1_PORT |= (1<<NEXT_KBD_LED1_BIT);
#define NEXT_KBD_LED1_OFF NEXT_KBD_LED1_PORT &= ~(1<<NEXT_KBD_LED1_BIT);
// corresponds to the Keyboard In wire on the NeXT connector
#define NEXT_KBD_OUT_PORT PORTD
#define NEXT_KBD_OUT_PIN PIND
#define NEXT_KBD_OUT_DDR DDRD
#define NEXT_KBD_OUT_BIT 1
// corresponds to the Keyboard Out wire on the NeXT connector
#define NEXT_KBD_IN_PORT PORTD
#define NEXT_KBD_IN_PIN PIND
#define NEXT_KBD_IN_DDR DDRD
#define NEXT_KBD_IN_BIT 0
// this pin is an input for the power key on the NeXT keyboard
// as the keyboard is powered on this should be normally high;
// if it is pulled low it means the power button is being preseed
#define NEXT_KBD_PWR_PORT PORTD
#define NEXT_KBD_PWR_PIN PIND
#define NEXT_KBD_PWR_DDR DDRD
#define NEXT_KBD_PWR_BIT 4
#endif
//================= End of TMK converter Configuration ==================
/* key combination for command */
#define IS_COMMAND() ( \
(keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))|| \