Spellchecking converter README files.

This commit is contained in:
Thomas Russell Murphy 2014-01-04 22:45:52 -05:00 committed by tmk
parent 6e9260cc17
commit 3ee5f565ae
8 changed files with 17 additions and 17 deletions

View File

@ -71,8 +71,8 @@ Notes
Many ADB keyboards has no discrimination between right modifier and left one,
you will always see left control even if you press right control key.
Apple Extended Keyboard and Apple Extended Keyboard II are the examples.
Though ADB protocol itsef has the ability of distinction between right and left.
And most ADB keyboard has no NKRO functionality, though ADB protocol itsef has that.
Though ADB protocol itself has the ability of distinction between right and left.
And most ADB keyboard has no NKRO functionality, though ADB protocol itself has that.
See protocol/adb.c for more info.
EOF

View File

@ -6,7 +6,7 @@ Target MCU is ATMega32u4 but other USB capable AVR will also work.
Hardware
--------
Connect RX, TX and GND to UART pin of AVR. Note that you may need line drvier/level shfiter like MAX232 to interface high voltage of RS-232C.
Connect RX, TX and GND to UART pin of AVR. Note that you may need line driver/level shifter like MAX232 to interface high voltage of RS-232C.

View File

@ -2,7 +2,7 @@ M0110/M0110A to USB keyboard converter
======================================
This firmware converts the protocol of Apple Macintosh keyboard **M0110**, **M0110A** and **M0120** into USB. Target of this project is USB AVR controller **ATmega32U4**. Using this converter you can revive these retro keyboards with modern computer.
Pics of **M0110 + M0120** and **M0110A**.
Pictures of **M0110 + M0120** and **M0110A**.
![M0110+M0120](http://i.imgur.com/dyvXb2Tm.jpg)
![M0110A](http://i.imgur.com/HuHOEoHm.jpg)
@ -31,7 +31,7 @@ Note that original cable used with Mac is **straight** while phone handset cable
<http://en.wikipedia.org/wiki/Modular_connector#4P4C>
Close-up pic of handset cable. You can see one end of plug has reverse color codes against the other. Click to enlarge.
Close-up picture of handset cable. You can see one end of plug has reverse color codes against the other. Click to enlarge.
[![4P4C cable](http://i.imgur.com/3S9P1mYm.jpg?1)](http://i.imgur.com/3S9P1mY.jpg?1)
[Teensy]: http://www.pjrc.com/teensy/
@ -43,12 +43,12 @@ Close-up pic of handset cable. You can see one end of plug has reverse color cod
![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png)
### Pull-up Registor
You may need pull-up registors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. **1k-10k Ohm** will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
### Pull-up Resistor
You may need pull-up resistors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. **1k-10k Ohm** will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
Building Frimware
Building Firmware
-----------------
To compile firmware you need AVR GCC. You can edit *Makefile* and *config.h* to change compile options and pin configuration.

View File

@ -16,7 +16,7 @@ Connector
(receptacle)
Wiring: You can change this with ediging config.h.
Wiring: You can change this with editing config.h.
Pin mini DIN MCU
----------------------------------
@ -34,7 +34,7 @@ Wiring: You can change this with ediging config.h.
Protocol
--------
Singnal: Asynchronous, Positive logic, 19200baud, Least bit first
Signal: Asynchronous, Positive logic, 19200baud, Least bit first
Frame format: 1-Start bit(Lo), 8-Data bits, Odd-Parity, 1-Stop bit
This converter uses software method for testing purpose. AVR UART engine will work better.

View File

@ -12,7 +12,7 @@ Following three methods are used to implement PS/2 signal handling.
### Interrupt driven(ps2_interrupt.c)
Uses pin interrupt to detect falling edge of clock line.
### USART hardware module(ps2_usart.c)
Uses AVR USART engine to recevie PS/2 signal.
Uses AVR USART engine to receive PS/2 signal.
To select method edit Makefile.
@ -31,7 +31,7 @@ In case of Teensy2.0(ATMega32U4):
To change pin configuration edit config.h.
Build Frimware
Build Firmware
--------------
Just run `make`:

View File

@ -34,11 +34,11 @@ Connector
Protocol
--------
Singnal: Asynchronous, Negative logic, 1200baud, No Flow control
Signal: Asynchronous, Negative logic, 1200baud, No Flow control
Frame format: 1-Start bit, 8-Data bits, No-Parity, 1-Stop bit
AVR USART engine expects positive logic while Sun keyboard signal is negative.
To use AVR UART engine you need exteral inverter in front of RX and TX pin.
To use AVR UART engine you need external inverter in front of RX and TX pin.
Otherwise you can software serial routine to communicate the keyboard.
This converter uses software method, you doesn't need any inverter part.

View File

@ -6,7 +6,7 @@ Hardware requirement
Arduino Leonardo
http://arduino.cc/en/Main/ArduinoBoardLeonardo
Circuit@Home USB Host Sheild 2.0
Circuit@Home USB Host Shield 2.0
http://www.circuitsathome.com/products-page/arduino-shields/usb-host-shield-2-0-for-arduino

View File

@ -12,7 +12,7 @@ X68000 keyboard has ALPS linear switches.
Hardware
--------
Target MCU is ATMega32u4 but other USB capable AVR will also work.
You can use PJRC Teensy as dev board.
You can use PJRC Teensy as development board.
http://www.pjrc.com/teensy/
Wiring:
@ -83,7 +83,7 @@ bit 6-0 following scan code
Data from computer
------------------
- LED contorol ON/OFF(0/1)
- LED control ON/OFF(0/1)
bit 7 1(fixed)
bit 6 全角
bit 5 ひらがな